Dell Wyse R class WES2009 4GF/2GR Guide d'installation

Installation GuideWyse® R Class Conversion to WES2009Wyse® USB Firmware ToolTM Release 1.13Products: R10L, R50L, R50LE, R90L, R90LE, R90L7Issue: 09071

6 Chapter 2Step 3: Install the Rx0L RAM ModuleWarningRAM modules may be susceptible to damage by Electro-Static Discharge (ESD). All industry-standard

3 Installing Rx0LE Flash and RAMThis chapter contains information for users of Wyse Rx0LE thin clients who must install new flash and/or RAM. If you a

8 Chapter 3ProceduresStep 1: Remove the Rx0LE Thin Client Left Side CoverCautionFollow all precautions listed in the Quick-Start Guide that came with

Installing Rx0LE Flash and RAM 9Step 2: Install the Rx0LE Flash ModuleWarningFlash modules may be susceptible to damage by Electro-Static Discharge (E

10 Chapter 3Figure 9 Removing the existing flash module3. Install the new flash module in the reverse order of removing the original flash module. Car

Installing Rx0LE Flash and RAM 11Step 3: Install the Rx0LE RAM ModuleWarningRAM modules may be susceptible to damage by Electro-Static Discharge (ESD)

12 Chapter 3This page intentionally blank.

4 Installing WES2009 FirmwareThis chapter includes the requirements and procedures you need to install and use Wyse USB Firmware Tool to update your t

14 Chapter 4ProceduresComplete the following procedures as an administrator (administrator privileges are required).Step 1: Copy the RX0L_LE 2G_4G WES

Installing WES2009 Firmware 15Figure 12 Wyse USB Firmware Tool wizard2. Click Next to open the Select an Option dialog box.Figure 13 Configuration opt

Copyright Notices© 2011, Wyse Technology Inc. All rights reserved.This manual and the software and firmware described in it are copyrighted. You may n

16 Chapter 46. (Optional) Leave the default-selected Preserve data partition check box (recommended in most cases) unless you do not want to preserve

Installing WES2009 Firmware 17Figure 17 Prepare USB drive12.Select the USB key onto which you want the configurations (you can use Refresh as needed t

18 Chapter 4Step 5: Verifying Thin Client OperationAfter the thin client displays the WES2009 desktop, you can verify the Version and that your genera

Installing WES2009 Firmware 19Figure 19 Placement of labels on the R50LE and R90LEStep 7: Obtain a Firmware UpdateAfter converting your thin clients,

20 Chapter 4TroubleshootingThis section contains general troubleshooting information.USB Keys - Troubleshooting Boot IssuesDue to different manufactur

Installing WES2009 Firmware 21This page intentionally blank.

Installation GuideWyse® R Class Conversion to WES2009Issue: 090711Written and published by: Wyse Technology Inc., September 2011Created using FrameMak

Contents1 Introduction 1Kit Contents 1Overview 2Wyse Technical Support 2Related Documentation and Services 2Wyse Online Community 22 Installing Rx0L F

iv ContentsThis page intentionally blank.

1 IntroductionThis guide provides the instructions you need to use Wyse® USB Firmware Tool to convert the following Wyse R class thin clients to WES20

2 Chapter 1The Conversion Software Assembly DVD-ROM contains:• A PDF of this Installation Guide• Wyse USB Firmware Tool v1.13 • RX0L_LE 2G_4G WES2009

2 Installing Rx0L Flash and RAMThis chapter contains information for users of Wyse Rx0L thin clients who must install new flash and/or RAM. If you are

4 Chapter 2ProceduresStep 1: Remove the Rx0L Thin Client Left Side CoverCautionFollow all precautions listed in the Quick-Start Guide that came with y

Installing Rx0L Flash and RAM 5Step 2: Install the Rx0L Flash ModuleWarningFlash modules may be susceptible to damage by Electro-Static Discharge (ESD